For many schools, hospitals, and manufacturing facilities, InformaCast is the platform behind emergency alerts and daily announcements. It decides what message goes out and where it goes. But the people in a building never interact with the software. What they hear comes from the speakers, amplifiers, and intercoms, which makes choosing the right speakers for InformaCast just as important as choosing the platform itself.
This post covers how Digital Acoustics works with InformaCast, which hardware fits which spaces, and how facilities with existing analog speakers can bring them into an InformaCast deployment.
What InformaCast Does
InformaCast, from Singlewire Software, is a mass notification platform that handles emergency alerts and everyday communication from a single system. It can send audio, text, and visual alerts to IP phones, IP speakers, overhead paging systems, desktops, and mobile devices.
Organizations in education, healthcare, manufacturing, and government use it for emergencies such as lockdowns and severe weather alerts. They also use it for routine work like bell schedules and facility-wide paging. In each case, InformaCast sends the message, and the hardware in each space has to deliver it clearly.
How Digital Acoustics Works With InformaCast
Digital Acoustics provides IP speakers and IP amplifiers built for InformaCast. InformaCast uses them for scheduled and live paging through Cisco Unified Communications Manager or other VoIP phone systems.
DA’s S3 firmware supports both InformaCast and SIP, and it follows Singlewire’s V1.2 IP Speaker Protocol specification. Facilities ordering for InformaCast should specify the InformaCast firmware option, which uses a SKU ending in -S3-IC. Because the firmware supports both protocols, the same hardware can receive InformaCast notifications and SIP pages from desk phones.
DA’s IP intercoms can also connect to InformaCast using DA’s custom firmware, so intercom locations can be part of the same system as the speakers.
Choosing the Right InformaCast Speakers
Every DA IP speaker for InformaCast is PoE powered and delivers up to 8 watts of audio. Each speaker needs only one network cable for both power and audio, with no separate electrical run. The right model depends on the space.
- 2′ x 2′ lay-in ceiling tile speaker: DA’s most popular model, because it is attractive and easy to install in drop ceilings.
- Wall mount speaker: A heavy duty, vandal resistant version is available for indoor or outdoor use.
- Slimline wall speaker: a lower profile option for smaller indoor areas.
- BiDirectional Hallway speaker: mounts on a wall or ceiling and covers hallways up to 12 by 100 feet.
The full lineup is on the IP speakers page.
Bringing Existing Analog Systems Into InformaCast
Many facilities already have analog speakers and amplifiers that still work well. Replacing them is not always necessary to use InformaCast.
The IP7-FX-S3-IC can connect an existing 70V analog system to InformaCast. Installed on the network, it feeds its line out into the inputs of the existing analog amplifier, so InformaCast messages play through the speakers already in place.
Digital Acoustics also offers IP amplifiers in 8, 25, and 40 watt models. They can drive a single 8 ohm speaker or a group of speakers on a 25/70V line using matching transformers, and they work with new or existing speakers.
This allows a facility to build out InformaCast coverage in phases. New areas can get IP speakers, while areas with working analog speakers can be connected through IP amplifiers.
Planning an InformaCast Deployment
A good deployment starts with where alerts need to reach rather than with hardware. Classrooms, hallways, gymnasiums, outdoor areas, and loud spaces each call for different speaker types and coverage. From there, decide which areas need new IP speakers and which can keep their analog speakers with an IP amplifier.
For setup, DA’s S3 IP Endpoint Configuration Guide, found on the S3 firmware page of the Digital Acoustics website, covers configuring DA devices with InformaCast. For help with speaker layout and system design, the Digital Acoustics PA and two-way communications design service works with facilities and integrators before installation begins.
To interact with every platform Digital Acoustics supports, visit the integrations page, or contact the Digital Acoustics team to plan your InformaCast deployment.

